Fix Hotspot Shield Bandwidth Exceeded, TCP Connect Wait, Auth Failure or Daemon Start Error

Hotspot Shield is in essence a uninhibited secretive secure VPN tunnel service so as to routes through a US head waiter with USA location IP direct. And consequently, it has been used not no more than on behalf of security unencrypted wireless connection connected to known WiFi access end, but and been used as a tool to access websites restricted no more than to visitors from United States, or as a ‘proxy’ to surf anonymously or download shared archive from RapidShare, MegaUpload, and so on.

Unfortunately, Hotspot Shield in a jiffy limit the uninhibited bandwidth management (data so as to been transmitted and tunneled through AnchorFree VPN server) to worthless 3 GB above a rolling 30 days dot. The limit is without problems rap especially as soon as watching videos on Hulu, Pandora or Veoh. When the bandwidth limit exceeded, user possibly will grow single of the following fault messages as soon as attempting to tie to Hotspot Shield VPN head waiter by the side of Hotspot Shield tie leaf.

State: Disconnected (Auth Failure)

State: Disconnected (Bandwidth Exceeded)

State: Daemon Start Error

State: TCP Connect Wait

After user hard-pressed the tie button, the state will switch in turn from Starting VPN Process to Unknown, to Waiting on behalf of head waiter, and at that time to Authenticating, and decisively by the side of Pulling Options ahead of looping repetitively and continuously again and again, until recurring single of the fault message over. And of path, the connection cannot be established, and VPN tunnel cannot be connected.

All these fault messages crop up on behalf of particular limited sanity so as to been detected by the Hotspot Shield head waiter, but ultimately it’s due to the sanity so as to the user has exceeded bandwidth limits, which at present harden by the side of 3 GB above a 30 days dot. Any user so as to has used more than 3 GB (used to be 10 GB previously) will not be able to log in until their preceding month of bandwidth management drops under 3 GB.

To quandary Bandwidth Exceeded, TCP Connect Wait, Auth Failure or Daemon Start Error as soon as concerning to Hotspot Shield VPN head waiter to confirm secure tunnel, user tolerate to beat and bypass the bandwidth limit. By properly, AnchorFree be supposed to tolerate provided user with option to procure extra bandwidth as soon as the user overuses and exceeds the limit. However, nearby is nix such options yet. So the workaround option is to reset the bandwidth limit.

MAC (Media Access Control) direct is and common as Ethernet Hardware Address (EHA) is a quasi-unique identifier attached to on the whole interact adapters (NIC or Network Interface Card). Each and each interact adapter has distinct unique MAC direct. Hotspot Shield bandwidth calculation is joined to the MAC direct. So by changing the MAC direct, Hotspot Shield will regard it as the latest PC, and has the bandwidth management starts from 0 (zero), as if the limit has been reset as user is still using the same practice.

Most interact interface certificate (NIC adapter) wires cloning of MAC direct. To switch the MAC direct of supported interact adapter, figure out the following:

Go to Start -> Control Panel.
Double click on Network Connections (inside Network and Internet Connections category).
Right click on the operating interact connection with interact adapter so as to you would like to switch the MAC direct (normally Local Area Network or Wireless Network Connection) and click on Properties.
Fashionable the General tab, click on the Configure button.
Click on Advanced tab.
Fashionable the Property section, exclusive and highlight Network Address or Locally Administered Address.
To the properly, “Not Present” means of communication button is by default selected as evaluate. Change the evaluate by clicking on means of communication button on behalf of Value:, and at that time type in a latest MAC direct to assign to the NIC.


The MAC direct consists of 6 pairs of statistics (0 – 9) and typescript (A – F) combination. For exemplar, 88-17-E8-90-E2-0A. When entering the latest MAC evaluate, omit the dash (-), on behalf of exemplar 8817E890E20A.

Click OK as soon as finished.
To verify the switch of MAC direct, turn to authority punctual, at that time type in single of the following commands:
Ipconfig /all
Clear config rdr

Reboot the workstation if profitable to give rise to the switch in effect.
Note so as to in Windows Vista, access to NIC’s properties is from Control Panel -> Network and Internet -> Network and Sharing Center -> Manage Network Connections. Alternatively, on behalf of both Windows XP and Windows Vista, turn to Device Manager and set off the properties dialog of NIC from nearby.